Weber 34 ICH replacement carb kit to suit Ford Transit 2 Ltr V4 models manufactured between 1967 – 1976
If you have a Transit 2 ltr from between 1981 and 1986, then you would need this carb.
If you have a Transit 2 ltr from after 1986, then you would need this carb.
If you have a Transit 1.7 ltr v4 model between 1967 and 1976, then you would need this carb.
Replaces Ford IV carburettor.
Kit comes with:-
- Weber 34ICH carburettor
- Manifold mounting adaptor
- Fuel pipe
- Full fittings kit & instructions
- Air filter
Standard jetting :-
- 29mm choke(fixed)
- 3.5 Auxiliary venturi
- 165 Main jet
- 50 Idle jet
- 190 Air corrector
- 55 Pump jet
- F6 Emulsion tube
- 175 Needle valve
Performance kit to allow fitment of 2 x genuine Spanish Weber 48DCO/SP carburettors to the Ford 2.0/2.1 OHC Pinto engine.
The carburettors come with a stock jetting which should be a good starting point – found here: 19630.007
Kit contains:
- 2 x Genuine Weber 48DCO/SP carburettors including 62mm trumpets
- 1 x Mangoletsi 4270 inlet manifold with special DCO/SP studs (not shown in photo)
- 1 x Webcon genuine twin cable linkage set
- Softmounts, studs, nuts, washers etc.
Good quality brand new stainless steel air filter, the same size as K&N small oval units.
Oval dimensions 180 x 118mm, 100mm deep.
Will fit:-
- DellOrto DHLA 40,45 and 48
- Weber DCOE 38,40,42,45 and 48 ( Note – hole size for trumpet is 48mm, which may need modification for slot in trumpets )
- Solex ADDHE.
Comes with air filter gasket.
Note – not suitable for use with full radius rampipes.
Cohline type 2240 Fuel hose with low permeation.
5.5mm bore x 11.5mm outer diameter.
Inside FPM/ECO, aramid brading inside, Outside ECO (abrasion resistant outer rubber layer)
DIN 73379-3E (edition 11/97)
- Working pressure 10Bar
- Testing pressure 20Bar
- Burst pressure 50bar
- Minimum bend radius 55mm
Suitable for commercial fuel including ethanol and Bio-diesel consisting of Rapeoilmethylester (RME Fuels)Â and E10.
Temperature range -40° to 125 °C, short term upto 140 °C
Sold per meter, max continous length 20mtr
Good quality brand new stainless steel air filter, the same size as K&N small oval units.
Oval dimensions 178 x 118mm,
83mm deep.
Height above top fixing stud 30mm
Depth of filter below bottom fixing stud 25mm
Up to 60mm long trumpets/stacks can be fitted inside these for optimum air flow, power and torque.
Will fit:-
- DellOrto DHLA 40,45 and 48 Weber
- DCOE 38,40,42,45 and 48 (Note – hole size for trumpet is 48mm, which may need modification for slot in trumpets )
- Solex ADDHE.
Comes with air filter gasket.
Note – not suitable for use with full radius rampipes.
(dhlafilter) (dcoefilter)
Cohline type 2192 Fuel injection hose with middle permeation.
12mm bore x 19mm outer diameter.
Inside layer NBR, Textile brading, Outer layer CR (Abrasion resistant rubber) DIN 73379-2A (edition 11/97)
- Working pressure 8Bar
- Testing pressure 20Bar
- Burst pressure 30bar
- Minimum bend radius 80mm
Suitable for commercial fuel including Super grades and E10.
Sold per meter, max continous length 20mtr
Genuine Weber, made in Spain, not a cheap Chinese copy
This carburettor is fitted with a manually operated (cable) cold start mechanism (choke), Cable not included.
Kit contains:
- Genuine Spanish Weber 32/36 DGV auto choke carburettor
- Inlet manifold
- Linkage kit
- Air filter
The carburettors come with a stock jetting which should be a good starting point – found here: 22680.005
Good quality brand new stainless steel air filter, the same size as K&N small oval units.
Oval dimensions 180 x 118mm, 63mm deep.
Will fit:-
- DellOrto DHLA 40,45 and 48
- Weber DCOE 38,40,42,45 and 48 ( Note – hole size for trumpet is 48mm, which may need modification for slot in trumpets )
- Solex ADDHE.
Comes with air filter gasket.
Note – not suitable for use with full radius rampipes.
(dhlafilter) (dcoefilter)
Cohline type 2192 Fuel injection hose with middle permeation.
9.5mm bore x 15.5mm outer diameter.
Inside layer NBR, Textile brading, Outer layer CR (Abrasion resistant rubber) DIN 73379-2A (edition 11/97)
- Working pressure 6Bar
- Testing pressure 20Bar
- Burst pressure 30bar
- Minimum bend radius 70mm
Suitable for commercial fuel including Super grades and E10.
Sold per meter, max continous length 20mtr
Cohline type 2192 Fuel injection hose with middle permeation.
7.5mm bore x 13.5mm outer diameter.
Inside layer NBR, Textile brading, Outer layer CR (Abrasion resistant rubber) DIN 73379-2A (edition 11/97)
- Working pressure 6Bar
- Testing pressure 20Bar
- Burst pressure 30bar
- Minimum bend radius 70mm
Suitable for commercial fuel including Super grades and E10.
Sold per meter, max continous length 20mtr
