Twin cable cable Magard style competition linkage kit to suit twin Dell’orto DHLA40, 45 & 48mm carburettors specially commissioned by Eurocarb ltd. Made to a very high standard with cast alloy base plates, bronze bushed swivel point and stainless steel fittings.
Designed for competition so choke cable holder will only fit with modification.
Will operate twin or triple carburettor setups. (additional levers may be required).
Kit includes:-
- Twin cables.
- Pedal mounting block (to adapt pedal rod to take twin cables).
- Twin return springs.
- Adjusting rod with metal ball and socket joints.
- All mounting hardware.
- Designed to be used with original levers fitted to carbs but these can be purchased here if needed: 10714L (modified) and balance lever 8304ASSEMBLY
NOTE : Carbs are not included and are shown for assembly purposes only.
Supplied by Webcon UK Good quality brand new pre -oiled chrome plated steel air filter, the same size as K&N small oval units.
Oval dimensions 182 x 120mm, 45mm deep.
Height of filter above top fixing stud 30mm
Depth of filter below bottom fixing stud 25mm
NOTE – Trumpets cannot be fitted inside this air filter.
Will fit:-
- DellOrto DHLA 40,45 and 48
- Weber DCOE 38,40,42,45 and 48
- Solex ADDHE.
- Comes with air filter gasket and nyloc fixings.
(dhlafilter) (dcoefilter)
CSP German made offset manifolds – machined to match DRLA & IDF 40 carburettors.
They are reinforced for port matching and each Pair comes with German made Gaskets in the right diameter and a complete fitting kit with metric Hardware.
Good engine builders recommend these manifolds for 40mm carburettors over the standard oversize type, claiming you can increase power by 5-10%
Supplied as a pair with:-
- Studs,nuts & washers for mounting carburettors
- Manifold to head gaskets
- Slim profile nuts for mounting onto head studs
Manifold height 155mm ( Approx. port centre to centre )
Note – not suitable for 44, 45 or 48mm carburettors.
A Weber performance kit to allow fitment of 2 x Genuine Spanish Weber 45DCOE 4 progression hole carburettors to BMW M10 2000/2002 engines,
E28 518
E30 318
E21 320
The carburettors come with a stock jetting found here: 19600.062
Kit contains:
- 2 x Weber 45DCOE carburettors
- 1 x Intake Manifold MW4810B
- 1 x Competition twin cable linkage set
- Soft mounts, studs, nuts, washers etc.
This manifold is for fitting a rubber mounted 28 or 30mm PHBH type carburettor to a 125/150/175cc cast/alloy type cylinders (not RT)
Fits all 125/150/175cc cylinders.
If you would wish to use this on a 125/ 150/ 175/ 190Â with VHSH 30
It comes with a stainless steel long bolt to replace the long inlet stud, otherwise it is very hard to fit the manifold without dropping the engine.
Requires the use of suitable mounting rubber and securing clips.
Custom Speed Parts safety-cut-out relay.
This relay allows the electric fuel pump to be automatically switched off when, e.g. in the event of an accident, the engine stops and the ignition remains switched on.
This device also protects the fuel pump against damage (risk of overheating), which can occur when the engine stops, but the ignition is on.
Comes with relay plus socket, universal wiring loom.
Note, This relay will cut the power to the pump, but if your fuel pump is the type that will allow fuel to flow through it when its not running fitting a solenoid like SOL002 may also be required.
Fitting instructions : CSP11-Relay-Information
Oval dimensions 182 x 120mm, 83mm deep.
Up to 60mm long trumpets/stacks can be fitted inside these for optimum air flow, power and torque.
Will fit:-
- Dellorto DRLA 36, 40, 45 and 48mm carburettors.
- Weber IDF 36, 40, 44 & 48mm carburettors.
Comes with air filter gasket
A Weber performance kit to allow fitment of 2 x Genuine Spanish Weber 40DCOE carburettors to Ford pre crossflow engines.
The carburettors come with a stock jetting found here:Â 19550.174
Kit contains:
- 2 x Weber 40DCOE carburettors
- 1 x Intake Manifold
- 1 x Twin cable linkage set
- Soft mounts, studs, nuts, washers etc.
This manifold fits Small Block engines with these rubber mounted carbs
- 25mm PHBL Dellorto
- 24mm TMÂ Mikuni
- 24mm PWK types
Fits type cast cylinders
- SR 175/190
- Mugello
- Original 125/150/175 barrel
- Casa
This inlet manifold does NOT fit the MB/BGM RT cylinders – these use the larger 200cc type stud spacing.
It comes with a stainless steel long bolt to replace the long inlet stud, otherwise it is very hard to fit the manifold without dropping the engine.
Requires the use of suitable mounting rubber and securing clips.
A Weber performance kit to allow fitment of a Genuine Spanish Weber 32/36 DGV carburettor to the Volvo B18/20 engines.
This kit offers an excellent balance of performance and economy, all at an extremely competitive price.
Please note: The photo used for this product shows a carburettor with a water choke fitted – This kit comes with a manual choke.
Kit contains:
- A Weber 32/36 DGV carburettor
- Intake Manifold
- Air filter
- Webcon linkage set
- Studs, nuts, & washersÂ
